J9772A Specifications
|
| Type |
Aruba 2530-48G-PoE+ Switch |
| System Specifications |
| Ports |
- · 48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX; Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
- · 4 fixed Gigabit Ethernet SFP ports
- · 1 Dual-personality (RJ-45 or USB micro-B) serial console port.
|
| Memory and processor |
Processor: ARM9E @ 800 MHz, 128 MB flash, 256 MB DDR3 DIMM; packet buffer size: 3 MB dynamically allocated. |
| Mounting |
Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting. |
| Management |
IMC - Intelligent Management Center; Command-Line Interface (CLI); Web browser; configuration menu; out-of-band management (serial RS-232C or Micro USB); IEEE 802.3 Ethernet MIB; Repeater MIB; Ethernet Interface MIB. |
| Performance (IPv6 Ready Certified) |
| 1000 Mb latency |
< 2.3 µs (LIFO 64-byte packets) |
| 100 Mb Latency |
< 7.4 µs (LIFO 64-byte packets) |
| Throughput |
Up to 77.3 million pps (64-byte packets) |
| Switching capacity |
104 Gb/s |
| MAC address table size |
16000 entries |
| Physical specifications |
| Dimensions (W x D x H) |
44.3 x 32.26 x 4.45 cm (17.44 x 13.00 x 1.75 in) (1U height) |
| Weight |
4.72 kg (10.4 lb) |
| Electrical specifications |
| Maximum heat dissipation |
236 BTU/hr (248.98 kJ/hr), (switch only: 236 BTU/hr; combined switch + max. PoE devices: 1624 BTU/hr) |
| Voltage |
100 - 127 / 200 - 240 V ac |
| Current |
5.8/2.9 A |
| Idle power1 |
40.1 W |
| Maximum power rating2 |
476 W |
| PoE power |
382 W |
| Frequency |
50/60 Hz |
| NOTE: 1: Idle power is the actual power consumption of the device with no ports connected.
2: Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. PoE power is the total power budget available to all PoE ports. |
| Environmental specifications |
| Operating temperature |
0° to 45°C (32° to 113°F) |
| Operating relative humidity |
15% to 95% @ 40°C (104°F), noncondensing |
| Non-operating/storage temperature |
-40° to 70°C (-40° to 158°F) |
| Non-operating/storage relative humidity |
15% to 90% @ 65°C (149°F), noncondensing |
| Altitude |
Up to 3 km (10,000 ft) |
| Acoustic |
Power: 33.6 dB, Pressure: 43.9 dB |
| Safety agency certifications |
| Safety |
UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825; IEC 60950-1; EN 60950-1 |
| NOTE: IEEE 802.3az applies to Gigabit models only; IEEE 802.3at and IEEE 802.3af apply to PoE+ models only. When using SFPs with this product, SFPs with revision "B" or later (product number ends with the letter "B" or later, e.g., J4858B, J4859C) are required. |
